Read the whole display
Say whether the message shows on the cooktop zones or the oven display, and what the display says.
Model-specific code library
We decode 12 Thermador range entries. Home Connect update codes are included.
dE on a Thermador range means the cooktop is in demo mode, so the zones do not heat. Trip the circuit breaker for 30 seconds, restore it, and touch any control within 3 minutes.
Read the dE checks17 researched range codes. What a panel message means depends on the model, so rely on the manual that came with yours.
dE on a Thermador range means the cooktop is in demo mode, so the zones do not heat. Trip the circuit breaker for 30 seconds, restore it, and touch any control within 3 minutes.
Check firstAn E with digits and a beep on a Thermador range is an error code the Thermador manual does not decode. Press TIMERS or any key to stop the beep, reset if necessary, and book a visit if it returns.
Reset once, then bookE0211 on a Thermador range appears during a Home Connect software update. The ranges page offers a resolution link and no steps of its own.
Check firstE0510 on a Thermador range is listed with E0211 and E1601 as a Home Connect software update code. The Thermador manual points to a resolution link.
Check firstE1601 on a Thermador range appears during a Home Connect software update, in the same entry as E0211 and E0510. Use the resolution link on the Thermador manual.
Check firstE7010 on a Thermador range means the cooktop cannot reach your home Wi-Fi or the hood. Switch the appliance off and on again; a one-off message goes away.
Check firstE7015 on a Thermador range means the electronics overheated and cooking zones were shut down. The ranges page lists it beside F2 (one zone) and beside F4 (all zones). Wait for cooling, then touch any control.
Cool down, then bookE9000 on a Thermador range means the supply voltage is outside the normal range. The Thermador manual has no owner step; have the supply checked by an electrician.
Check supplyE9010 on a Thermador range has the same wording as E9000: the supply voltage is outside the normal range. Have the supply checked and book a visit.
Check supplyF1 on a Thermador range means a cooking zone overheated and shut off to protect the work surface. Wait for the electronics to cool, then switch the zone back on.
Cool down, then bookF2 on a Thermador range means the electronics overheated and the related cooking zone was shut down. Wait for cooling, then touch any control.
Cool down, then bookF4 on a Thermador range means the electronics overheated and all cooking zones were shut down. Wait for the electronics to cool, then touch any control.
Cool down, then bookF5 flashing alternately with the power level and a tone on a Thermador range warns that hot cookware is near the control panel. Remove it and you can keep cooking.
Check firstF5 with a tone and no flashing on a Thermador range means hot cookware near the control panel already made the zone shut off. Remove it, wait a few seconds, then touch any control.
Check firstF6 on a Thermador range shares the F1 entry: a cooking zone overheated and shut off to protect the work surface. Wait for cooling, then switch the zone back on.
Cool down, then bookF8 with H or h on a Thermador range means a cooking zone ran without input for a long time and the automatic time limit switched it off. Touch a control, then set that zone again.
InformationalU400 on a Thermador range means the supply voltage is outside the normal operating range, in the wording E9000 and E9010 share. No owner step is printed; have an electrician check the supply.
Check supply
We decode 12 Thermador range entries. Home Connect update codes are included.
We read the induction range section of Thermador's US ranges support page, which lists no models. Range oven cavities are covered by the oven entries. Thermador's Home Connect app messages (404, C7101, E7101, H1011 to H9400) are not tied to one appliance in the source, so they are not published here.
Say whether the message shows on the cooktop zones or the oven display, and what the display says.
Let the range cool and keep power off for any wiring work.
On a Thermador Pro range, each rangetop burner has its own igniter and should catch within four seconds. If one will not, Thermador’s first suspect is a burner cap sitting out of alignment. Reseat it, dry everything, and check the knob. Several burners dead, or sparking that never stops, needs a technician.
On a Thermador range the oven door latch can stay engaged, so the door stops short of shut. Thermador’s support page gives a one-minute breaker reset, and for self-cleaning ovens a short trip into the Self-Clean cycle to free the latch. Try those, and call us if the latch stays out.
Match your model to the guide it shipped with. See how we research these pages.
We read the induction range section of Thermador's US ranges support page, which lists no models. Range oven cavities are covered by the oven entries. Thermador's Home Connect app messages (404, C7101, E7101, H1011 to H9400) are not tied to one appliance in the source, so they are not published here.
Photograph the entire range panel along with the rating plate. Note what the appliance was doing when the message came up, and do not lean on the explanation for a different unit.
A phrase people once typed into a search box is not evidence from the manufacturer. When our range manuals leave a message unexplained, we print its name, send you toward help and name no cause.
Open the Thermador manuals in this range library and match the model printed on each cover to your rating plate. A different series comes with its own use-and-care guide.