Start from the symptom
Thermador range burner won’t light.
On a Thermador Pro range, each rangetop burner has its own igniter and should catch within four seconds. If one will not, Thermador’s first suspect is a burner cap sitting out of alignment. Reseat it, dry everything, and check the knob. Several burners dead, or sparking that never stops, needs a technician.

Start with safe observations.
Turn the appliance off and pull the plug before doing any check yourself. Look out for standing water and sharp edges. Never handle a wet plug, remove a service panel or step beyond what your model's guide permits an owner.
- 1
Time the attempt
Each burner has an electronic igniter that sparks when the knob is turned. The range guide expects a flame in four seconds or less, so a burner that takes longer counts as a problem.
- 2
Seat the cap
When one burner is dark and the rest light, the support page points at a cap out of alignment. Turn the cap until its tabs drop into the notches on the burner base.
- 3
Dry the burners
After cleaning, dry the burners completely. Moisture left on the rangetop or inside the base can keep a burner dark, or keep the spark running until it dries.
- 4
Check the knob
A knob pressed in or stuck makes the igniters spark even with the range off. On models made after September 2018, a knob held past the child lock position keeps the spark going.
- 5
Power outage
After a cut, turn every knob to OFF. Only burners without the ExtraLow feature can be lit by hand while the power is out.
- 6
Draft
A draft can blow a flame out. Select models try to relight it with the re-ignition feature, so a clicking burner may just be doing that.
Systems a technician may investigate.
These parts relate to the symptom, though what you noticed cannot show that any single one has failed.

Gas burner igniter
Thermador gas burners light with electronic igniters. The guides say they are fragile, spark when a burner is turned on, and should be cleaned with a damp cotton swab. Constant sparking has a short list of causes on the support page. Never take a gas appliance apart.

STAR burner
STAR burner is Thermador's name for the sealed gas burner on its rangetops, ranges and gas cooktops. The rangetop guide says no burner parts under the surface need cleaning or adjusting. When one burner stays dark, Thermador's support page checks the burner cap first.

ExtraLow burner
An ExtraLow (XLO) burner is a Thermador STAR burner that cycles its flame on and off to hold a very low temperature. A slightly taller flame at simmer than on a standard burner is normal. These burners cannot be lit by hand during a power failure.
If the display adds a code.
No message is tied directly to this topic.
No other researched dishwasher message is tied to this topic. Compare the exact wording with your model's manual and never substitute another message from the library.
See the research statusLook after it the way this appliance's own guide describes.
When observation becomes a service request.
Leave internal testing to a technician.
You smell gas. Turn all knobs off, stay clear of flames and switches, and call the gas company from outside.
Two or more burners will not light after the caps were reseated and dried.
The igniters keep sparking after everything dried out.
One burner needs repeated attempts before it catches.
Arrange a diagnosticSources and model boundaries.
These documents back up the Thermador range burner won’t light guidance. Choose the manual written for your model.
- Troubleshooting | Gas Cooktops & Rangetops Support | Thermador
- Use and Care Guide, Professional Series Pro Grand and Pro Harmony Ranges PRD364WDGU PRD364WIGU PRD366WGU PRD486WDGU PRD486WIGU and others
Match your model to the guide it shipped with. See how we research these pages.
Why will only one of my burners light?
Thermador’s support page gives a cap out of alignment as the cause. Adjust the cap so the tabs fit the notches in the base, then try that burner again.
Is clicking after the flame lights normal?
Sometimes. Select models relight a flame that is disturbed, and clicking also follows spills or water on the cooktop. If it carries on once dry, a technician has to open the range.
Why do the igniters click when the range is off?
After power is first connected or restored they may spark once or twice. A burner knob that is stuck or pushed in also makes them spark.
Is hand-lighting possible when the power is out?
Only for burners without ExtraLow. Turn every knob to OFF first and follow the electrical failure steps in the range guide.
Thermador messages, symptoms, parts, repair visits
Move from the message to your next step.
Thermador range burner won’t light
On a Thermador Pro range, each rangetop burner has its own igniter and should catch within four seconds. If one will not, Thermador’s first suspect is a burner cap sitting out of alignment. Reseat it, dry everything, and check the knob. Several burners dead, or sparking that never stops, needs a technician.
STAR burner
STAR burner is Thermador's name for the sealed gas burner on its rangetops, ranges and gas cooktops. The rangetop guide says no burner parts under the surface need cleaning or adjusting. When one burner stays dark, Thermador's support page checks the burner cap first.
Range repair
Book a diagnostic made for your exact model and performed at the appliance itself.
Find your metro
Where the offices are, and what to tell us about getting in.