Before work starts
Your technician reviews the issue with you and settles the cost before any repair starts. For built-in units the final figure comes after an on-site look.
Independent appliance repair
Book a visit for a Thermador Pro Grand or Pro Harmony range, or a Professional rangetop, when a burner stays dark, sparks nonstop, or the display shows a code such as F1, F5, dE or U400. A Thermador grill or griddle accessory is covered here too. Gas safety comes first.


On a Thermador Pro range, each rangetop burner has its own igniter and should catch within four seconds. If one will not, Thermador’s first suspect is a burner cap sitting out of alignment. Reseat it, dry everything, and check the knob. Several burners dead, or sparking that never stops, needs a technician.

On a Thermador range the oven door latch can stay engaged, so the door stops short of shut. Thermador’s support page gives a one-minute breaker reset, and for self-cleaning ovens a short trip into the Self-Clean cycle to free the latch. Try those, and call us if the latch stays out.
dE on a Thermador range means the cooktop is in demo mode, so the zones do not heat. Trip the circuit breaker for 30 seconds, restore it, and touch any control within 3 minutes.
E0211 on a Thermador range appears during a Home Connect software update. The ranges page offers a resolution link and no steps of its own.
E1601 on a Thermador range appears during a Home Connect software update, in the same entry as E0211 and E0510. Use the resolution link on the Thermador manual.
E0510 on a Thermador range is listed with E0211 and E1601 as a Home Connect software update code. The Thermador manual points to a resolution link.
Part names come only after the technician has examined the range in person. The quote comes first; nothing is ordered unless you agree.

STAR burner is Thermador's name for the sealed gas burner on its rangetops, ranges and gas cooktops. The rangetop guide says no burner parts under the surface need cleaning or adjusting. When one burner stays dark, Thermador's support page checks the burner cap first.

Thermador gas burners light with electronic igniters. The guides say they are fragile, spark when a burner is turned on, and should be cleaned with a damp cotton swab. Constant sparking has a short list of causes on the support page. Never take a gas appliance apart.

An ExtraLow (XLO) burner is a Thermador STAR burner that cycles its flame on and off to hold a very low temperature. A slightly taller flame at simmer than on a standard burner is normal. These burners cannot be lit by hand during a power failure.

The door latch locks a Thermador oven door during self-clean. If it will not retract and the door will not close, Thermador asks you to open the oven's circuit for a minute and close it again. For a self-cleaning oven it adds a 2-minute Self-Clean start, then exit.
What to expect.
Every step explained in advance.

Choose your appliance, whether range, oven or refrigeration, and tell us how it is behaving.

The technician inspects the unit, reviews the cause with you and agrees the cost before starting the work.

After the repair, the technician tests the appliance and explains the result, so you know what changed.
If you smell gas, turn all knobs to OFF, open windows and book a visit. Thermador says to wait at least 1 minute before relighting a burner that did not ignite after 15 seconds.
If only one burner stays dark, Thermador's page asks for the cap to be aligned so its tabs sit in the notches of the base.
E9000, E9010 and U400 point to the voltage reaching the range. Thermador lists no owner step, so an electrician checks the supply.
Thermador's support site lists safety notices, among them a Range Tipping Safety Notice and one for Professional 48-inch gas ranges. Read the ones for your model.
A burner stays dark with its cap seated, or the sparking never stops.
A supply code (E9000, E9010 or U400) or the same F code returns.
You smell gas.
Arrange a diagnosticYour technician reviews the issue with you and settles the cost before any repair starts. For built-in units the final figure comes after an on-site look.
Repairs under Thermador's manufacturer warranty belong with Thermador. For the work we carry out, we provide our own workmanship warranty.
There is no separate grill page. Thermador's range guides name a grill plate accessory and a griddle; book a visit and say which one you have.
On models where all igniters spark, the cooktop guide says they do so when any single burner is turned on. Do not touch burners then.
The entry says demo mode is on, which leaves the cooking zones cold. Remove power for 30 seconds, then touch any control within 3 minutes.
If your range is still inside the manufacturer's warranty, that coverage stays with the manufacturer. Once it has ended, we are glad to visit.
Thermador messages, symptoms, parts, repair visits
dE on a Thermador range means the cooktop is in demo mode, so the zones do not heat. Trip the circuit breaker for 30 seconds, restore it, and touch any control within 3 minutes.
On a Thermador Pro range, each rangetop burner has its own igniter and should catch within four seconds. If one will not, Thermador’s first suspect is a burner cap sitting out of alignment. Reseat it, dry everything, and check the knob. Several burners dead, or sparking that never stops, needs a technician.
The door latch locks a Thermador oven door during self-clean. If it will not retract and the door will not close, Thermador asks you to open the oven's circuit for a minute and close it again. For a self-cleaning oven it adds a 2-minute Self-Clean start, then exit.
Book a diagnostic made for your exact model and performed at the appliance itself.
Where the offices are, and what to tell us about getting in.