What it means
E1601 on a Thermador range appears during a Home Connect software update, in the same entry as E0211 and E0510. Use the resolution link on the Thermador manual.
Thermador range E1601 / Home Connect messages
E1601 on a Thermador range appears during a Home Connect software update, in the same entry as E0211 and E0510. Use the resolution link on the Thermador manual.
Also appears as E1601
E1601 on a Thermador range appears during a Home Connect software update, in the same entry as E0211 and E0510. Use the resolution link on the Thermador manual.
E1601 accompanies a Home Connect software update.
The code stays after the update finishes.
Your Thermador steps, stored on this device only

E1601 accompanies a Home Connect software update.

See whether the update completed.

The ranges page provides it for E0211, E1601 and E0510.

If E1601 stays, book a visit.
Give us your model number and the checks you already made, then start your request below.
Book a visitA simplified drawing, since the layout shifts from one model to the next. Tap any outlined part for its photo and the check that goes with it.
A Home Connect update error code, listed beside E0211 and E0510 on the ranges page.
Read the supporting manualThe Thermador manual calls it an update code and not a failure.
Read the supporting manualThe manual does not separate them.
Read the supporting manualThe Pro Grand and Pro Harmony range guide splits the update into two steps. The download runs while you keep using the range as normal. Installation takes a few minutes, and the range cannot be used during it.
Read the supporting manualManufacturer document
Thermador / BSH Home Appliances (thermador.com/us support page)
Undated web page; fetched 12.11.2026 / entry "E0211, E1601, E0510 appear during a Home Connect software update"
Manufacturer document
BSH Home Appliances Corporation (Thermador US manual PDF, media3.bsh-group.com)
PDF created 12.05.2025; file tag _A (no printed edition date read) / PDF p27
Manufacturer document
Thermador / BSH Home Appliances (thermador.com/us page)
Undated web page; fetched 12.11.2026 / entry "What Happens if I See an Error Display on the Screen? E0211, E1610, E0510"
Source: the ranges page of Thermador's oven support section, entry for E0211, E1601 and E0510. The Pro Grand and Pro Harmony range guide describes the update steps.
The Thermador manual does not say. It treats E1601 as a Home Connect update code, and the Pro Grand and Pro Harmony guide says the range cannot be used during installation, which takes a few minutes.
Updates run through Home Connect, so yes, the range needs its connection to the app. The guide says you must be a registered Home Connect user with the app installed.
Behind the resolution link on the Thermador manual. Thermador's update page gives steps for ovens only, and the ranges entry prints none of them.
Book a visit if E1601 stays after the update has finished and you have followed the resolution link.
The Pro Grand and Pro Harmony range guide, section 10.5. It says you must be a registered Home Connect user with the app installed, and that security updates should be installed as soon as possible.
Thermador messages, symptoms, parts, repair visits
An E with digits and a beep on a Thermador range is an error code the Thermador manual does not decode. Press TIMERS or any key to stop the beep, reset if necessary, and book a visit if it returns.
On a Thermador Pro range, each rangetop burner has its own igniter and should catch within four seconds. If one will not, Thermador’s first suspect is a burner cap sitting out of alignment. Reseat it, dry everything, and check the knob. Several burners dead, or sparking that never stops, needs a technician.
Book a diagnostic made for your exact model and performed at the appliance itself.
Where the offices are, and what to tell us about getting in.