Inside the appliance
ExtraLow burner. In plain English.
An ExtraLow (XLO) burner is a Thermador STAR burner that cycles its flame on and off to hold a very low temperature. A slightly taller flame at simmer than on a standard burner is normal. These burners cannot be lit by hand during a power failure.

Where it fits.
ExtraLow burner in the appliance
The ExtraLow range is marked on the control knob of the burners that have the feature.
The picture stands for a type of component. Which replacement suits your model is a separate question.
What shifts when this system needs a look.
ExtraLow burner concerns may show up next to a drop in performance or a message that keeps returning. Testing comes before any verdict on the component.

Thermador gas burner won't light
When one Thermador burner will not light while the rest do, the support page points to the burner cap: it is out of alignment, and its tabs must sit in the notches on the burner base. The cooktop guide adds a 4-second rule and clean, dry igniter ports. Gas odor means shut the unit off and book a visit.

Thermador gas igniter keeps clicking
Thermador's page lists four causes for sparking that will not stop or starts with the cooktop off: knobs left in the lighting or spark position, a draft working on the re-ignition feature, water on the surface, or a knob held down past the child lock position. Dismantling a gas appliance is a job for a trained technician.
Owner care, within the model instructions.
Turn the appliance off and pull the plug before doing any check yourself. Look out for standing water and sharp edges. Never handle a wet plug, remove a service panel or step beyond what your model's guide permits an owner.
- 1
Know the cycle
The rangetop guide describes a 60-second cycle, as little as 10 seconds on and 50 seconds off, to keep food warm with less stirring.
- 2
Expect a higher simmer flame
The guide says the XLO burner shows a slightly higher flame at simmer than a standard STAR burner and calls this normal.
- 3
Never match-light it
In a power failure only burners without the ExtraLow feature can be lit by hand. Turn every knob to OFF first.
Cleaning or replacement?
Leave internal testing to a technician.
An XLO burner will not light and the others do.
The flame does not cycle on and off in the XLO range.
Arrange a diagnosticSources and model boundaries.
These documents back up the ExtraLow burner guidance. Choose the manual written for your model.
- Use and Care Guide, Professional Series Rangetops PCG305W PCG366W PCG364WD PCG486WD
- Use and Care Guide, Professional Series Pro Grand and Pro Harmony Ranges PRD364WDGU PRD364WIGU PRD366WGU PRD486WDGU PRD486WIGU and others
- Use and Care Guide, Masterpiece Series Gas Cooktop SGS SGSX SGSP SGSXP
Match your model to the guide it shipped with. See how we research these pages.
Does an ExtraLow burner turn itself off?
It cycles the flame on and off. The guide describes a 60-second revolution that keeps the temperature very low.
Why is the simmer flame taller?
Thermador says the XLO burner at simmer shows a slightly higher flame than a standard STAR burner, and that this is normal.
Does Sabbath mode affect it?
The Pro range guide says Sabbath mode deactivates the STAR burners with the ExtraLow feature; standard gas burners stay usable.
When should I book?
When an XLO burner will not light or hold its cycle after the cap and ports are checked.
Thermador messages, symptoms, parts, repair visits
Move from the message to your next step.
Thermador range burner won’t light
On a Thermador Pro range, each rangetop burner has its own igniter and should catch within four seconds. If one will not, Thermador’s first suspect is a burner cap sitting out of alignment. Reseat it, dry everything, and check the knob. Several burners dead, or sparking that never stops, needs a technician.
Range repair
Book a diagnostic made for your exact model and performed at the appliance itself.
Find your metro
Where the offices are, and what to tell us about getting in.

