Start from the symptom
Thermador cooktop gas burner won't light.
When one Thermador burner will not light while the rest do, the support page points to the burner cap: it is out of alignment, and its tabs must sit in the notches on the burner base. The cooktop guide adds a 4-second rule and clean, dry igniter ports. Gas odor means shut the unit off and book a visit.

Start with safe observations.
Turn the appliance off and pull the plug before doing any check yourself. Look out for standing water and sharp edges. Never handle a wet plug, remove a service panel or step beyond what your model's guide permits an owner.
- 1
Turn the burner off
The guide says that if a burner has not lit within 4 seconds, turn it off rather than leaving the knob on.
- 2
Reseat the cap
The support page's cause is a cap out of alignment. Lift it and set it back so its tabs fit the notches on the base. The guide also asks that each cap go on its matching size and letter.
- 3
Check the igniter
The guide says the igniter should be clean and dry. Keep water and food off it, and let a wet cooktop dry.
- 4
Clean the igniter ports
The guide asks you to clean these after a boilover or when a burner will not light although the igniters click.
- 5
Try the knob again
With the cap seated and the igniter dry, turn the knob to the lighting position once more and watch for the flame.
Systems a technician may investigate.
Part names come only after the technician has examined the cooktop in person. The quote comes first; nothing is ordered unless you agree.

STAR burner
STAR burner is Thermador's name for the sealed gas burner on its rangetops, ranges and gas cooktops. The rangetop guide says no burner parts under the surface need cleaning or adjusting. When one burner stays dark, Thermador's support page checks the burner cap first.

Gas burner igniter
Thermador gas burners light with electronic igniters. The guides say they are fragile, spark when a burner is turned on, and should be cleaned with a damp cotton swab. Constant sparking has a short list of causes on the support page. Never take a gas appliance apart.

ExtraLow burner
An ExtraLow (XLO) burner is a Thermador STAR burner that cycles its flame on and off to hold a very low temperature. A slightly taller flame at simmer than on a standard burner is normal. These burners cannot be lit by hand during a power failure.

Induction cooking sensor
The wireless cooking sensor on a Thermador induction cooktop reads pan temperature. E8204 means its battery is nearly drained: replace the 3V CR2032. E8205 means the connection dropped: switch the sensor function off and on. E8206 calls the sensor defective.
If the display adds a code.
No message is tied directly to this topic.
No other researched dishwasher message is tied to this topic. Compare the exact wording with your model's manual and never substitute another message from the library.
See the research statusRead the related care guide.

Induction zone dark? Wait, touch, or call
On a Thermador induction cooktop, F1, F6, F2, F4 and F5 mean the electronics or the glass got too hot, so you let them cool and touch a control. F8 with an H or h is a time limit that one touch resets. Other codes need a technician. [1][3][4]

dE, UP, SAB, LOCK, Demo: not errors
dE, UP, Sabbath, Lock and Demo are settings or notices in Thermador's pages and manuals, not errors. dE and Demo stop heating or cooling on purpose, UP reports a software update, and Sabbath and Lock switch off buttons and alarms. Each one clears with a short step. [1][3][5][6][7]
When observation becomes a service request.
Leave internal testing to a technician.
A burner still will not light after the cap, igniter and port checks.
You smell gas at any time. Shut off the unit first.
Several burners will not light at once.
The burner caps are chipped or will not sit flat.
Arrange a diagnosticSources and model boundaries.
These documents back up the Thermador gas burner won't light guidance. Choose the manual written for your model.
- Troubleshooting | Gas Cooktops & Rangetops Support | Thermador
- Use and care guide, Masterpiece Series Gas Cooktop SGS SGSX SGSP SGSXP
- Use and care guide, Masterpiece Series Gas Cooktop SGS SGSX SGSP SGSXP
Match your model to the guide it shipped with. See how we research these pages.
Why will only one Thermador burner light?
The support page names a burner cap out of alignment. Reseat it so the tabs fit the notches on the burner base and test that burner again.
What does the 4-second note mean?
The guide says to turn a burner off if it has not lit within 4 seconds, then check the cap position and that the igniter is clean and dry.
What if gas is in the air while I try a burner?
The guide says to shut off the unit at once and have a technician diagnose it. Stop trying to light anything while that smell is present.
Can I clean the igniter ports myself?
The guide asks owners to keep them clean and says to do so after boilovers or when the igniters click but no flame appears. It lists no tool or part for that.
Does this cover a Thermador range?
The wording comes from the gas cooktop and rangetop support page and one cooktop guide. A range oven is a separate appliance with its own entries.
Thermador messages, symptoms, parts, repair visits
Move from the message to your next step.
Thermador gas burner won't light
When one Thermador burner will not light while the rest do, the support page points to the burner cap: it is out of alignment, and its tabs must sit in the notches on the burner base. The cooktop guide adds a 4-second rule and clean, dry igniter ports. Gas odor means shut the unit off and book a visit.
Cooktop repair
Book a diagnostic made for your exact model and performed at the appliance itself.
Find your metro
Where the offices are, and what to tell us about getting in.