Inside the appliance
STAR burner. In plain English.
STAR burner is Thermador's name for the sealed gas burner on its rangetops, ranges and gas cooktops. The rangetop guide says no burner parts under the surface need cleaning or adjusting. When one burner stays dark, Thermador's support page checks the burner cap first.

Where it fits.
STAR burner in the appliance
On the surface of the rangetop, range or cooktop, under a flat cap that rests on a star-shaped base.
The picture stands for a type of component. Which replacement suits your model is a separate question.
What shifts when this system needs a look.
STAR burner concerns may show up next to a drop in performance or a message that keeps returning. Testing comes before any verdict on the component.

Thermador gas burner won't light
When one Thermador burner will not light while the rest do, the support page points to the burner cap: it is out of alignment, and its tabs must sit in the notches on the burner base. The cooktop guide adds a 4-second rule and clean, dry igniter ports. Gas odor means shut the unit off and book a visit.

Thermador gas igniter keeps clicking
Thermador's page lists four causes for sparking that will not stop or starts with the cooktop off: knobs left in the lighting or spark position, a draft working on the re-ignition feature, water on the surface, or a knob held down past the child lock position. Dismantling a gas appliance is a job for a trained technician.
Owner care, within the model instructions.
Turn the appliance off and pull the plug before doing any check yourself. Look out for standing water and sharp edges. Never handle a wet plug, remove a service panel or step beyond what your model's guide permits an owner.
- 1
Seat the burner cap
Thermador's page: when one burner stays dark and the others light, align the cap so its tabs sit in the notches of the base.
- 2
Match the cap letters
The rangetop guide says each cap has a letter (B, D or F) cast underneath that matches a letter on its burner base.
- 3
Clear the ports
The guide says that sparks coming on and off can mean clogged burner ports; clean the cap's ports with a wire, needle or straightened paper clip.
Cleaning or replacement?
Leave internal testing to a technician.
One burner stays dark with its cap seated and its ports clear.
You smell gas. Turn the burner knobs off, ventilate the room and book a visit.
Arrange a diagnosticSources and model boundaries.
These documents back up the STAR burner guidance. Choose the manual written for your model.
- Troubleshooting | Gas Cooktops & Rangetops Support | Thermador
- Use and Care Guide, Professional Series Rangetops PCG305W PCG366W PCG364WD PCG486WD
- Use and Care Guide, Professional Series Pro Grand and Pro Harmony Ranges PRD364WDGU PRD364WIGU PRD366WGU PRD486WDGU PRD486WIGU and others
Match your model to the guide it shipped with. See how we research these pages.
Can I adjust a STAR burner?
The rangetop guide says the burners are sealed and have no parts under the rangetop to clean, disassemble or adjust.
What if one burner stays dark but the others light?
Thermador's first check is the cap alignment: the tabs should fit the notches on the burner base.
What if the flame goes out?
The Pro range guide says the STAR burners have a re-ignition feature: the igniter lights the flame again if it blows out.
When should I book?
When a burner stays dark with a seated cap and clear ports, or whenever gas is in the air.
Thermador messages, symptoms, parts, repair visits
Move from the message to your next step.
Thermador range burner won’t light
On a Thermador Pro range, each rangetop burner has its own igniter and should catch within four seconds. If one will not, Thermador’s first suspect is a burner cap sitting out of alignment. Reseat it, dry everything, and check the knob. Several burners dead, or sparking that never stops, needs a technician.
Range repair
Book a diagnostic made for your exact model and performed at the appliance itself.
Find your metro
Where the offices are, and what to tell us about getting in.

