Start from the symptom
Thermador cooktop gas igniter keeps clicking.
Thermador's page lists four causes for sparking that will not stop or starts with the cooktop off: knobs left in the lighting or spark position, a draft working on the re-ignition feature, water on the surface, or a knob held down past the child lock position. Dismantling a gas appliance is a job for a trained technician.

Start with safe observations.
Turn the appliance off and pull the plug before doing any check yourself. Look out for standing water and sharp edges. Never handle a wet plug, remove a service panel or step beyond what your model's guide permits an owner.
- 1
Check every knob
Make sure each knob sits at OFF. Thermador says knobs in the LIGHTING / SPARK position keep the igniters sparking, and a stuck or pushed-in knob sparks at OFF.
- 2
Look for a draft
Select models re-ignite a flame that was blown out or disturbed. Close a window or turn down a fan aimed at the burners.
- 3
Dry the surface
Water from heavy cleaning or a boilover that reached the appliance can cause continuous sparking. Thermador says this clears when the surface dries.
- 4
Release the knob
On cooktops bought after September 2018, a knob held down past the child lock position keeps the spark going. Let go and turn it to OFF.
- 5
Note power-up sparks
After first power-up or a power outage, the igniters may spark once or twice with the cooktop off. Thermador describes that as expected.
Systems a technician may investigate.
Part names come only after the technician has examined the cooktop in person. The quote comes first; nothing is ordered unless you agree.

STAR burner
STAR burner is Thermador's name for the sealed gas burner on its rangetops, ranges and gas cooktops. The rangetop guide says no burner parts under the surface need cleaning or adjusting. When one burner stays dark, Thermador's support page checks the burner cap first.

Gas burner igniter
Thermador gas burners light with electronic igniters. The guides say they are fragile, spark when a burner is turned on, and should be cleaned with a damp cotton swab. Constant sparking has a short list of causes on the support page. Never take a gas appliance apart.

ExtraLow burner
An ExtraLow (XLO) burner is a Thermador STAR burner that cycles its flame on and off to hold a very low temperature. A slightly taller flame at simmer than on a standard burner is normal. These burners cannot be lit by hand during a power failure.

Induction cooking sensor
The wireless cooking sensor on a Thermador induction cooktop reads pan temperature. E8204 means its battery is nearly drained: replace the 3V CR2032. E8205 means the connection dropped: switch the sensor function off and on. E8206 calls the sensor defective.
If the display adds a code.
No message is tied directly to this topic.
No other researched dishwasher message is tied to this topic. Compare the exact wording with your model's manual and never substitute another message from the library.
See the research statusRead the related care guide.

Induction zone dark? Wait, touch, or call
On a Thermador induction cooktop, F1, F6, F2, F4 and F5 mean the electronics or the glass got too hot, so you let them cool and touch a control. F8 with an H or h is a time limit that one touch resets. Other codes need a technician. [1][3][4]

dE, UP, SAB, LOCK, Demo: not errors
dE, UP, Sabbath, Lock and Demo are settings or notices in Thermador's pages and manuals, not errors. dE and Demo stop heating or cooling on purpose, UP reports a software update, and Sabbath and Lock switch off buttons and alarms. Each one clears with a short step. [1][3][5][6][7]
When observation becomes a service request.
Leave internal testing to a technician.
Sparking continues after the knobs, draft and dry-surface checks.
A burner sparks at OFF and the knob is not stuck.
You smell gas. Shut off the unit and stay clear.
Water went into the appliance and sparking has not stopped after it dried.
Arrange a diagnosticSources and model boundaries.
These documents back up the Thermador gas igniter keeps clicking guidance. Choose the manual written for your model.
- Troubleshooting | Gas Cooktops & Rangetops Support | Thermador
- Use and care guide, Masterpiece Series Gas Cooktop SGS SGSX SGSP SGSXP
Match your model to the guide it shipped with. See how we research these pages.
Is a clicking igniter at power-up normal?
Thermador says that after the first power-up or an outage, igniters may spark once or twice with the cooktop off. Check that no knob is stuck or pushed in.
Why does it click when the burner is already lit?
The guide says that with a flame present and a Low setting, the igniter may spark now and then. A wet or soiled igniter can also spark continuously.
What does re-ignition do?
On select models it is part of flame recognition. It tries to relight a flame that has been blown out or disturbed, so a draft can make it spark.
Can I take the cooktop apart to fix it?
No. Thermador says never to dismantle a gas appliance unless you are qualified. Book a visit if the sparking continues after the checks.
How does the child lock figure in?
On cooktops bought after September 2018, Thermador says the spark runs on if a knob is held down past the child lock position. Release the knob and set it to OFF.
Thermador messages, symptoms, parts, repair visits
Move from the message to your next step.
Thermador gas burner won't light
When one Thermador burner will not light while the rest do, the support page points to the burner cap: it is out of alignment, and its tabs must sit in the notches on the burner base. The cooktop guide adds a 4-second rule and clean, dry igniter ports. Gas odor means shut the unit off and book a visit.
Cooktop repair
Book a diagnostic made for your exact model and performed at the appliance itself.
Find your metro
Where the offices are, and what to tell us about getting in.