Diagnostics and repair
Our technicians look the appliance over before they propose any work. When a part is needed, an OEM part for your model is ordered in.
The care journal
Something quit working? Begin with the checks your manual permits, and learn the point where a technician should step in.

For a group of control-board E-codes, Thermador's support page tells you to take the dishwasher's breaker to off for 30 seconds and then back to on. The DWHD660EFM manual asks for at least 2 minutes. Should the code return after one reset, stop repeating it and arrange a visit. [1][2]

Thermador's built-in cooling alarms come in three kinds. A door alarm means a door stayed open and closing it stops the sound. A freezer temperature alarm reports the warmest reading it saw. HI on an under-counter unit means the inside got too warm. [1][2][4]

Note the letter and number, and whether a power level is blinking beside it. F5 means two different things depending on that blink.
Read the full sequence
When one Thermador burner will not light while the rest do, the support page points to the burner cap: it is out of alignment, and its tabs must sit in the notches on the burner base. The cooktop guide adds a 4-second rule and clean, dry igniter ports. Gas odor means shut the unit off and book a visit.

Thermador's page lists four causes for sparking that will not stop or starts with the cooktop off: knobs left in the lighting or spark position, a draft working on the re-ignition feature, water on the surface, or a knob held down past the child lock position. Dismantling a gas appliance is a job for a trained technician.

Thermador says humming, buzzing and crackling on an induction cooktop come from the cookware and are normal, not a sign of malfunction. A whistle means an empty pan on a live zone and stops once you add food or water. The Freedom guide ties a deep hum to high power or a pan too small for the zone.

The wireless cooking sensor on a Thermador induction cooktop reads pan temperature. E8204 means its battery is nearly drained: replace the 3V CR2032. E8205 means the connection dropped: switch the sensor function off and on. E8206 calls the sensor defective.

STAR burner is Thermador's name for the sealed gas burner on its rangetops, ranges and gas cooktops. The rangetop guide says no burner parts under the surface need cleaning or adjusting. When one burner stays dark, Thermador's support page checks the burner cap first.
F1 on a Thermador induction cooktop means a cooking zone overheated and switched itself off to protect the work surface. Give the electronics time to cool down before you turn the zone back on.
F6 means a cooking zone overheated and shut itself off to protect the work surface, in the same wording Thermador uses for F1. Wait for the electronics to cool, then switch the zone back on.
E7015 means the electronics of a Thermador induction cooktop overheated and the related cooking zone was switched off. Wait for the electronics to cool, touch a control, and cook again once the message is gone.
E8207 is one of five codes Thermador lists for overheated electronics on induction cooktops: the related cooking zone has shut off. Let the electronics cool, touch any control, and cook once the message has gone.
E8208 is listed with F2, F4, E7015 and E8207 as an electronics overheating message on Thermador induction cooktops. The related zone is off; wait for it to cool, touch any control, then carry on.
Our technicians look the appliance over before they propose any work. When a part is needed, an OEM part for your model is ordered in.
Repairs under Thermador's manufacturer warranty belong with Thermador. For the work we carry out, we provide our own workmanship warranty.
It walks one symptom, such as an oven that heats unevenly, through the steps a homeowner can try without risk.
Where the manual or safety says so. We then suggest booking a visit.
No. Models differ, so each guide names the series its source covers.
The model, the message, and what you tried. Photos help.
Thermador messages, symptoms, parts, repair visits
On a Thermador Pro range, each rangetop burner has its own igniter and should catch within four seconds. If one will not, Thermador’s first suspect is a burner cap sitting out of alignment. Reseat it, dry everything, and check the knob. Several burners dead, or sparking that never stops, needs a technician.
Book a diagnostic made for your exact model and performed at the appliance itself.
Where the offices are, and what to tell us about getting in.