Troubleshooting

The lights came back, the code did not leave one clean reset, then a decision

For a group of control-board E-codes, Thermador's support page tells you to take the dishwasher's breaker to off for 30 seconds and then back to on. The DWHD660EFM manual asks for at least 2 minutes. Should the code return after one reset, stop repeating it and arrange a visit. [1][2]

A hand holds a phone with a blue timer ring beside an open breaker panel with one breaker off, a dishwasher behind.
Experienced techniciansWarranty on our workmanshipOEM parts available on orderUpfront pricing, agreed before work
On this page
Key points
  • Twelve codes on the support page start with a 30-second breaker reset, E9001 among them. 1
  • The manual for the DWHD660EFM says to wait at least 2 minutes, so use the longer wait. 2
  • Neither source says a power cut causes these codes; the reset is simply the manufacturer's first step. 12
  • Codes such as E0105, E0110, E04 and E6160 come with no reset step on the page. 1

Why does a Thermador dishwasher show an E-code after the power comes back?#

Neither Thermador source ties a power cut to these codes. What the support page does is give a breaker reset as the first step for a whole group of them, so a code that appears around an outage deserves exactly that step. 1

Think of it as restarting a computer. The dishwasher's control board runs checks when it gets power, and a code from one of those checks can stay on the display. Removing power fully and restoring it either clears it or proves it is real. This guide lays out which codes the page answers this way, how long the sources say to wait, and when a second try is a waste of time.

Which codes does Thermador answer with a breaker reset?#

Twelve entries on the dishwasher error-code page open with a reset. Eleven of them use the same wording, and E9001 adds an electrician for repeat cases. The table groups them by what the page says they describe. 1

CodeWhat the page says it is
E0100Heat pump motor circuit on the main control board
E0103, E0107A relay on the main control board
E0106Wash arm diverter circuit on the board
E2030, E6001Internal heater of the heat pump
E2120Heater of the Zeolite (Crystal Dry) chamber
E2130Fan motor of the Zeolite chamber
E6002Heat pump blocked
E6900Detergent dispenser solenoid circuit
E8000Door sensor circuit
E9001House power to the unit too low

Three neighbors on the same page get no reset line: E0105 and E04 (the self-test found a problem with the heater electronics), and E0110 (electronics not communicating). E6160 (a Zone Control spray arm that cannot find its reference position) also has none. 1 For those, a reset costs nothing but the page does not promise a result from it. Our dishwasher library has rows for E0100, E6002 and E9001, among others.

How long is the wait before power returns?#

The two sources disagree, so take the longer one. The support page names 30 seconds at the breaker; the DWHD660EFM manual says wait at least 2 minutes after switching off at the breaker or unplugging. 12

Both describe the same action, and a longer wait cannot hurt. The manual's version comes with a sequence: press the main switch button for about 4 seconds first, and if the problem occurs again, switch the appliance off, cut power for 2 minutes or more, restore it, then switch on. 2 Unsure whether your model matches the DWHD660EFM, the 2-minute wait still fits both readings.

What are the steps for a clean reset?#

Keep it simple and do it once. The point is to see whether the code is a one-time hiccup or a repeat. 12

  1. 1

    Write the code down#

    Copy every digit, for example E0103. The page answers each code separately. 1

    An open dishwasher door whose steel control strip shows small lit indicator dots, with plates and a glass in the racks.
  2. 2

    Switch the breaker off#

    Use the breaker or fuse that feeds the dishwasher in the electrical panel. 12

    A hand flips one breaker in an open gray electrical panel, the other breakers in a tidy column.
  3. 3

    Wait at least 2 minutes#

    The page names 30 seconds; the manual names 2 minutes, so take the longer. 12

    A hand holds an analog stopwatch beside an open electrical panel with rows of toggle breakers.
  4. 4

    Restore power and start a short cycle#

    Check the display. A cleared code means the reset worked. If it returns, stop and do not repeat the cycle. 12

    A closed stainless dishwasher set between navy cabinets, with a faint blue glow along the top edge under a long bar handle.

If the dishwasher is wired directly into the house circuit, leave the wiring itself alone and use only the breaker switch.

What does E9001 have to do with a power cut?#

E9001 is the one code where the supply itself is the issue. The page says the house power reaching the unit is too low, advises the 30-second reset and, if it happens again, an electrician to check the incoming voltage. 1

The DWHD660EFM manual says the same in other words: the voltage is too low, there is no problem with the appliance, and an electrician should test the voltage and the installation. 2 A similar line on the page covers E27 as a supply voltage that is too low and states it is not an error of the appliance. 1 After an outage or a brownout, these are the codes most likely to be about the grid rather than the machine, but only an electrician can confirm that.

What if every light flashes after the power returns?#

Hold off for now. The manual says that when every indicator light comes on or flashes, a software update may be installing, and that this can take about 30 minutes. 2

If the dishwasher is not ready after 30 minutes, the manual's next step is the 4-second press on the main switch button, which resets and restarts it. 2 A power cut in the middle of an update is the situation in which that matters most. We do not know whether your dishwasher was updating when the power failed, so use the display as the guide: steady lights and a ready display mean you can start a cycle.

Is a code with water involved different?#

Yes. Two code families involve water protection and the page treats them differently from board codes. E15 and E3100 report that the safety switch sensed water in the base and the leak protection has engaged, and the page wants the water inflow closed first. 1

The manual's table for E:30-00 and E:31-00 gives the same steps: shut the supply valve and then ask for service. 2 A breaker reset does not belong here. Water in the base is a leak question, and the code will not clear while there is water. Our dishwasher service page describes what a visit covers.

When is one reset enough, and when is it time to call?#

One properly timed reset is enough to learn something. If the identical code is back, if your code is one without a reset line, or if the breaker trips the moment the dishwasher starts, the next step is a technician. 12

The support page lists a manufacturer phone number for that. Prefer someone independent? Arrange a technician through our site. Dishwashers still under Thermador's coverage go back to Thermador, and our workmanship carries its own warranty. Before anyone touches the machine, the price is agreed with you; the final amount is set after the technician has looked at it at your address.

Sources#

  1. Error Codes | Dishwashers Support | ThermadorThermador (thermador.com, US support site) · Page undated; retrieved 12.11.2026 · Entries E0100, E0103, E0105, E0106, E0107, E0110, E2030, E2120, E2130, E6001, E6002, E6900, E8000, E9001, E27
  2. Use and care GUIDE: Dishwasher DWHD660EFMThermador (BSH Home Appliances), en-us edition · File tag 9001862916_C · PDF pages 33-35 (troubleshooting table)

Here to help

Good questions.
Clear answers.

Talk to our team
Can a power cut really put an E-code on my Thermador dishwasher?

Thermador's pages never say that a cut causes these codes. They list a breaker reset as the first step for a group of control-board codes, and a power interruption is a natural time to meet them. Treat the reset as a test, not a diagnosis. [1]

How long must the breaker stay off?

The support page says 30 seconds. For the DWHD660EFM, the manual wants a wait of 2 minutes or longer after switching off at the breaker or unplugging. The sources differ, so the longer wait is the safer reading, and nothing is lost by it. [1][2]

Does E9001 mean my dishwasher is broken?

Not by itself. The page describes E9001 as house power to the unit being too low and asks for a 30-second reset first; the manual says the appliance itself is fine and sends you to an electrician. [1][2]

Will the reset erase my cycle settings?

The pages are silent on that. They describe a reset only as removing power, then restoring it. If a setting is lost afterward, set it again from the use and care guide. A separate factory reset is a different function. [1][2]

What if all the indicator lights flash after the power returns?

The manual says a software update may be installing and can take about 30 minutes. Wait that long first. If the dishwasher is still not ready, hold the main switch for about 4 seconds to reset it. [2]

Let’s take care of it.

One burner, two burners,
or the whole range.