Start from the symptom
Thermador dishwasher not draining.
For a Thermador dishwasher that leaves water behind, the error-code page lists the same four steps for E22, E24 and E25: filter, drain pump cover, drain hose and air gap or hose. The DWHD660EFM guide adds two checks for a display reading E:61-03: remove the garbage disposal plug and keep a high loop in the hose.

Start with safe observations.
Turn the appliance off and pull the plug before doing any check yourself. Look out for standing water and sharp edges. Never handle a wet plug, remove a service panel or step beyond what your model's guide permits an owner.
- 1
Switch the power off
Turn the dishwasher off, and cut power at the breaker before reaching into the base.
- 2
Wash the filter
E22 starts with a blocked filter. Hold it under running water and scrub with a little gentle soap on a soft brush.
- 3
Open the drain pump cover
Lift it off, clear out leftover water and loose debris, then press it back until it clicks closed. A loose cover is one listed cause.
- 4
Straighten the pump hose
Thermador says a kinked or sharply bent hose can stop the water leaving.
- 5
Check the disposal plug and loop
The DWHD660EFM guide says E:61-03 can mean the garbage disposal is still plugged or the hose is kinked. It also asks for a high loop in the drain hose.
- 6
Clear the air gap or hose
Power down, look at the air gap, then detach the drain hose into a bucket, clear it, reattach it and start a rinse to test.
Systems a technician may investigate.
Part names come only after the technician has examined the dishwasher in person. The quote comes first; nothing is ordered unless you agree.

Dishwasher drain pump
The drain pump sends used wash water out of a Thermador dishwasher. Thermador's pages tie it to E22, E23, E24, E25, E6101, E6102 and E6103. Owner steps: reseat the cover over the pump, straighten the drain hose and clear the air gap. A code that keeps returning means a visit.

Dishwasher filter system
The filter system catches food particles before they reach the pump. Thermador lists a blocked filter first under E22 and E9240, and says to rinse it under running water with mild soap and a soft brush. The DWHD660EFM guide says to check it after every cycle.

Dishwasher flow meter
The flow meter measures water entering a Thermador dishwasher. Thermador's E14 and E3000 entries describe a flow meter failure or a problem with the fill path and print no owner step. E16, E17, E18, E3200, E3300 and E3400 add inlet hose and supply checks.

Dishwasher heat pump
A Thermador dishwasher heats its wash water through a heat pump. The support page names it in E12 and E2060 (limescale), E2030 and E6001 (internal heater) and E6002 (blocked). For limescale it says to run a descaler and use softener salt where the unit has a softener.

Dishwasher Zeolite chamber
Zeolite is a mineral in a Thermador dishwasher's drying system that holds moisture, then gives heat back. Thermador's page ties E2120 to the chamber heater and E2130 to the fan motor. The DWHD660EFM guide reads E:21-30 as dishes covering the intake.

Dishwasher main control board
The main control board runs a Thermador dishwasher's circuits. Thermador's page names it in E0100, E0103, E0106 and E0107, and E0110 describes electronics that miscommunicate. For the first four it asks for the breaker to stay open for 30 seconds.
If the display adds a code.
Drain pump
E22 has several possible causes on Thermador's page: a blocked filter, a blocked drain pump or loose pump cover, a kinked pump hose, or a clogged air gap or drain hose. Start with the filter, then work down the list.
Drain pump
E24 has three listed causes on Thermador's page: a blocked drain pump or loose cover, a kinked pump hose, and a clogged air gap or drain hose. Open the pump cover first, then check the hose and air gap.
Drain pump
E25 shares its checklist with E24: a blocked drain pump or loose cover, a kinked pump hose, and a clogged air gap or drain hose. Work through them in that order and finish with a rinse cycle.
Drain pump
E23 on Thermador's page says the drain pump is blocked, clogged or faulty, with no owner step printed. Look for standing water, note whether the tub drains at all, and book a visit.
Read the related care guide.

E-code after a power cut? Reset the breaker once
For a group of control-board E-codes, Thermador's support page tells you to take the dishwasher's breaker to off for 30 seconds and then back to on. The DWHD660EFM manual asks for at least 2 minutes. Should the code return after one reset, stop repeating it and arrange a visit. [1][2]

E2060 or E12? It's limescale, descale it
E2060 and E12 on a Thermador dishwasher both point to scale inside the heat pump, and the cure is a descaling run with a dishwasher descaler. Thermador suggests descaling every three to six months, and softener salt helps prevent a repeat on models that use it. [1][2]
When observation becomes a service request.
Leave internal testing to a technician.
E22, E24 or E25 comes back after all of the checks above.
Your display shows E23, which Thermador's page does not give a home remedy.
Water is still sitting in the tub after the rinse test.
The drain pump cover has a crack, or it refuses to snap shut.
Arrange a diagnosticSources and model boundaries.
These documents back up the Thermador dishwasher not draining guidance. Choose the manual written for your model.
- Error Codes | Dishwashers Support | Thermador
- Error Codes | Dishwashers Support | Thermador
- Error Codes | Dishwashers Support | Thermador
- Use and care guide, Dishwasher DWHD660EFM (en-us)
Match your model to the guide it shipped with. See how we research these pages.
Which Thermador dishwasher codes point to draining?
E22, E24 and E25 carry the filter, pump, hose and air gap checks. E23 reads as a blocked, clogged or defective drain pump, with no step listed for owners.
What does E:61-03 mean?
The DWHD660EFM guide says the disposal plug may still be in, or the drain hose is kinked, and that this is not an appliance error. Remove the plug, straighten the hose and retry.
Do I need a high loop in the drain hose?
The guide's table asks for one, since debris flushed back into the hose can block it. Confirm the loop is present and clear.
Is E:61-03 an appliance error?
No. The guide's table labels it not an appliance error and lists the plugged disposal, a kinked hose and a loose pump cover as the causes to clear.
Can I run a test after clearing the hose?
Yes. Yes. Thermador says to switch the dishwasher back on and start a rinse cycle to see whether it now empties. If water remains, book a visit.
Thermador messages, symptoms, parts, repair visits
Move from the message to your next step.
E22
E22 has several possible causes on Thermador's page: a blocked filter, a blocked drain pump or loose pump cover, a kinked pump hose, or a clogged air gap or drain hose. Start with the filter, then work down the list.
Thermador dishwasher not draining
For a Thermador dishwasher that leaves water behind, the error-code page lists the same four steps for E22, E24 and E25: filter, drain pump cover, drain hose and air gap or hose. The DWHD660EFM guide adds two checks for a display reading E:61-03: remove the garbage disposal plug and keep a high loop in the hose.
Dishwasher repair
Book a diagnostic made for your exact model and performed at the appliance itself.
Find your metro
Where the offices are, and what to tell us about getting in.