Before work starts
Your technician reviews the issue with you and settles the cost before any repair starts. For built-in units the final figure comes after an on-site look.
Independent appliance repair
Book a visit for a Thermador dishwasher that shows E15, E22 or E24, will not drain, leaves water in the base or throws a four-digit code. We cover the codes on Thermador's dishwasher page. With water on the floor, shut the supply and the breaker first.

E04 is the short form of the heater electronics self-test message on a Thermador dishwasher. The Thermador manual prints no owner step; note the display and model and book a visit.
E12 means limescale has built up in the heat pump. Run a dishwasher descaler through the machine to clear hard-water deposits, and use softener salt if your dishwasher has a softener.
E14 means the flow meter has failed or water is not entering the dishwasher through the filling system. The Thermador manual gives no owner step; note the display and book a visit.
E15 means the safety switch found water in the base of the Thermador dishwasher and the leakage protection activated. Shut the water valve that feeds the dishwasher, then book a technician.
E16 suggests water may not be getting into the Thermador dishwasher through the filling system. Inspect the inlet hose for kinks and damage.
Part names come only after the technician has examined the dishwasher in person. The quote comes first; nothing is ordered unless you agree.

The drain pump sends used wash water out of a Thermador dishwasher. Thermador's pages tie it to E22, E23, E24, E25, E6101, E6102 and E6103. Owner steps: reseat the cover over the pump, straighten the drain hose and clear the air gap. A code that keeps returning means a visit.

The filter system catches food particles before they reach the pump. Thermador lists a blocked filter first under E22 and E9240, and says to rinse it under running water with mild soap and a soft brush. The DWHD660EFM guide says to check it after every cycle.

The flow meter measures water entering a Thermador dishwasher. Thermador's E14 and E3000 entries describe a flow meter failure or a problem with the fill path and print no owner step. E16, E17, E18, E3200, E3300 and E3400 add inlet hose and supply checks.

A Thermador dishwasher heats its wash water through a heat pump. The support page names it in E12 and E2060 (limescale), E2030 and E6001 (internal heater) and E6002 (blocked). For limescale it says to run a descaler and use softener salt where the unit has a softener.

Zeolite is a mineral in a Thermador dishwasher's drying system that holds moisture, then gives heat back. Thermador's page ties E2120 to the chamber heater and E2130 to the fan motor. The DWHD660EFM guide reads E:21-30 as dishes covering the intake.

The main control board runs a Thermador dishwasher's circuits. Thermador's page names it in E0100, E0103, E0106 and E0107, and E0110 describes electronics that miscommunicate. For the first four it asks for the breaker to stay open for 30 seconds.
What to expect.
Every step explained in advance.

Choose your appliance, whether range, oven or refrigeration, and tell us how it is behaving.

The technician inspects the unit, reviews the cause with you and agrees the cost before starting the work.

After the repair, the technician tests the appliance and explains the result, so you know what changed.
E15 means the leak protection tripped. Stop the water inflow, as Thermador says, and open the breaker before anyone steps onto a wet floor.
E22, E24 and E25 ask for the filter, pump cover, drain hose and air gap to be checked in that order.
E16, E17, E18, E3200, E3300 and E3400 ask for an open supply and an inlet hose that is not kinked or damaged.
Four-digit board and heater codes such as E0100 or E2030: flip the breaker off, count 30 seconds, flip it back.
E15 shows, or water stands in the base.
A drain or fill code returns after the checks.
A four-digit code comes back after the half-minute breaker cycle.
Arrange a diagnosticYour technician reviews the issue with you and settles the cost before any repair starts. For built-in units the final figure comes after an on-site look.
Repairs under Thermador's manufacturer warranty belong with Thermador. For the work we carry out, we provide our own workmanship warranty.
Water was sensed in the base and the leakage protection stepped in. Stop the water inflow and book a visit.
No. Thermador says UP means the dishwasher's software was updated; press any program button to clear it.
No. Both point to low supply voltage. For E27 Thermador adds that it is not a dishwasher failure; an electrician checks the home's voltage.
If your dishwasher is still inside the manufacturer's warranty, that coverage stays with the manufacturer. Once it has ended, we are glad to visit.
Thermador messages, symptoms, parts, repair visits
E04 is the short form of the heater electronics self-test message on a Thermador dishwasher. The Thermador manual prints no owner step; note the display and model and book a visit.
For a Thermador dishwasher that leaves water behind, the error-code page lists the same four steps for E22, E24 and E25: filter, drain pump cover, drain hose and air gap or hose. The DWHD660EFM guide adds two checks for a display reading E:61-03: remove the garbage disposal plug and keep a high loop in the hose.
The drain pump sends used wash water out of a Thermador dishwasher. Thermador's pages tie it to E22, E23, E24, E25, E6101, E6102 and E6103. Owner steps: reseat the cover over the pump, straighten the drain hose and clear the air gap. A code that keeps returning means a visit.
Book a diagnostic made for your exact model and performed at the appliance itself.
Where the offices are, and what to tell us about getting in.