Thermador dishwasher E0100 / Control board and sensors

Thermador dishwasher
code E0100

Dishwasher / display reference

E0100 on a Thermador dishwasher reports a problem in the heat pump motor circuit on the main control board. Switch the dishwasher's breaker off for 30 seconds and back on; if the message stays, a technician is needed.

Also appears as E0100

Last reviewed

Dishwasher / display reference
Meaning
E0100 on a Thermador dishwasher reports a problem in the heat pump motor circuit on the main control board. Switch the dishwasher's breaker off for 30 seconds and back on; if the message stays, a technician is needed.
Who handles it
Reset once, then book
Related codes
Source
Error Codes | Dishwashers Support | Thermador

What Thermador dishwasher E0100 means.

What it means

E0100 on a Thermador dishwasher reports a problem in the heat pump motor circuit on the main control board. Switch the dishwasher's breaker off for 30 seconds and back on; if the message stays, a technician is needed.

What you can safely check

If a cycle is running, let the dishwasher stand idle and leave the door closed.

When to call a technician

E0100 returns after the reset.

Your Thermador steps, stored on this device only

Safe checks, in order.

0 of 4 checks done
  1. Thermador dishwasher E0100: Dishwasher with the toe-kick panel off, exposing a control board in a white housing, and its three-prong power plug lying unplugged on the floor.
    Illustration. Follow your model’s instructions.
    Before you begin

    Stop the cycle

    If a cycle is running, let the dishwasher stand idle and leave the door closed.

  2. Dishwashers in a thoughtfully designed home
    Illustration. Follow your model’s instructions.
    Check 2

    Find the breaker

    Switch the dishwasher's breaker off at the electrical panel.

  3. A built-in refrigerator panel flush with cabinetry
    Illustration. Follow your model’s instructions.
    Check 3

    Wait 30 seconds

    Thermador gives that exact pause before power is restored.

  4. A technician in a navy shirt holds a tablet showing five empty checkboxes beside a built-in wall oven in a navy kitchen.
    Illustration. Follow your model’s instructions.
    Check 4

    Restore power and test

    Switch on and run a short cycle. A repeat means the board needs a technician.

Is E0100 still on the display?

Give us your model number and the checks you already made, then start your request below.

Book a visit

The control and its wiring.

Conceptual dishwasher sectionKeypadControl boardMotor wiringHeater wiring1234
  1. 1Keypad
  2. 3Motor wiring
  3. 4Heater wiring

A simplified drawing, since the layout shifts from one model to the next. Tap any outlined part for its photo and the check that goes with it.

Parts behind the message.

A white pouch and a small measuring cup stand on marble beside an open empty dishwasher with two racks.

Component reference

Dishwasher heat pump

A Thermador dishwasher heats its wash water through a heat pump.

Read the definition
A close view of a gray breaker panel with a column of black breakers, one handle shifted, blurred kitchen behind.

Component reference

Dishwasher main control board

The main control board runs a Thermador dishwasher's circuits.

Read the definition

A little more context.

What does E0100 point to?

The Thermador manual names the heat pump motor circuit on the main control board. It does not say which component failed.

Read the supporting manual

How does E0100 differ from E0103 and E0107?

Those two are relay messages on the same board. E0100 is about the motor circuit of the heat pump.

Read the supporting manual

The manual behind the message.

Manufacturer document

Error Codes | Dishwashers Support | Thermador

Thermador / BSH Home Appliances (thermador.com/us support page)

Undated web page; fetched 12.11.2026 / entry "E0100"

Source: the dishwasher error-code page from Thermador (no model listed). Heat pump dishwashers use the E0xxx style.

Here to help

Good questions.
Clear answers.

Talk to our team
Does E0100 mean the heat pump has failed?

The Thermador manual speaks of a circuit on the control board, not the pump itself.

How long must power stay off?

Keep the breaker off for 30 seconds, as Thermador prints it, then switch it back on. Book a technician if E0100 stays.

Can I keep washing?

If a cycle will not run, stop and book a visit.

What if E0100 returns?

Tell us the model and whether the heating worked.

Let’s take care of it.

One burner, two burners,
or the whole range.