Thermador dishwasher E0103 / Control board and sensors

Thermador dishwasher
code E0103

Dishwasher / display reference

E0103 means a relay on the main control board of a Thermador dishwasher has a problem. Reset power at the breaker for 30 seconds; if the message stays, call for a technician.

Also appears as E0103

Last reviewed

Dishwasher / display reference
Meaning
E0103 means a relay on the main control board of a Thermador dishwasher has a problem. Reset power at the breaker for 30 seconds; if the message stays, call for a technician.
Who handles it
Reset once, then book
Related codes
Source
Error Codes | Dishwashers Support | Thermador

What Thermador dishwasher E0103 means.

What it means

E0103 means a relay on the main control board of a Thermador dishwasher has a problem. Reset power at the breaker for 30 seconds; if the message stays, call for a technician.

What you can safely check

Remember when the dishwasher stopped.

When to call a technician

E0103 comes back after the reset.

Your Thermador steps, stored on this device only

Safe checks, in order.

0 of 4 checks done
  1. Thermador dishwasher E0103: Dishwasher with the toe-kick panel off, exposing a control board in a white housing, and its three-prong power plug lying unplugged on the floor.
    Illustration. Follow your model’s instructions.
    Before you begin

    Note the cycle stage

    Remember when the dishwasher stopped.

  2. Dishwashers in a thoughtfully designed home
    Illustration. Follow your model’s instructions.
    Check 2

    Reset at the breaker

    Switch the dishwasher's breaker off for 30 seconds, then on.

  3. A built-in refrigerator panel flush with cabinetry
    Illustration. Follow your model’s instructions.
    Check 3

    Test a cycle

    Run a short cycle after power returns.

  4. A technician in a navy shirt holds a tablet showing five empty checkboxes beside a built-in wall oven in a navy kitchen.
    Illustration. Follow your model’s instructions.
    Check 4

    Book a visit

    A relay on the board is not an owner repair.

Is E0103 still on the display?

Give us your model number and the checks you already made, then start your request below.

Book a visit

The control and its wiring.

Conceptual dishwasher sectionKeypadControl boardMotor wiringHeater wiring1234
  1. 1Keypad
  2. 3Motor wiring
  3. 4Heater wiring

A simplified drawing, since the layout shifts from one model to the next. Tap any outlined part for its photo and the check that goes with it.

Parts behind the message.

A close view of a gray breaker panel with a column of black breakers, one handle shifted, blurred kitchen behind.

Component reference

Dishwasher main control board

The main control board runs a Thermador dishwasher's circuits.

Read the definition

A little more context.

What is a relay in E0103?

The Thermador manual says only that a relay on the main control board has a problem or error, with no part list.

Read the supporting manual

How does E0103 differ from E0107?

The manual prints the same relay wording for both, so the sources do not separate them.

Read the supporting manual

The manual behind the message.

Manufacturer document

Error Codes | Dishwashers Support | Thermador

Thermador / BSH Home Appliances (thermador.com/us support page)

Undated web page; fetched 12.11.2026 / entry "E0103"

Source: the dishwasher error-code page from Thermador, entry E0103.

Here to help

Good questions.
Clear answers.

Talk to our team
Does E0103 mean a new board?

The Thermador manual does not say that. It says a relay on the main control board has a problem, and board work is a technician job rather than an owner decision.

Is it safe to run?

Reset once, but do not keep forcing cycles. The Thermador manual gives only the 30-second breaker reset; if the message stays, call for a technician.

Which relay?

The Thermador manual does not specify. It says only that a relay on the main control board has a problem or error, with no part list.

What if it repeats?

Book a visit if E0103 comes back after the 30-second breaker reset and a short test cycle. A relay on the board is not an owner repair.

Let’s take care of it.

One burner, two burners,
or the whole range.