Diagnostics and repair
Our technicians look the appliance over before they propose any work. When a part is needed, an OEM part for your model is ordered in.
The care journal
Small habits that keep a Thermador kitchen running well: hood filters, water filters, descaling and the parts an owner can safely reach.

When a Thermador built-in coffee machine asks for a descaling, cleaning or combined program, run it with the tablets and steps your manual names, rinse the brewing unit with water only, and avoid vinegar and citric acid. If descaling is ignored, the machine eventually locks. [1][2][3]

The FILTER light on a Thermador hood is a reminder, not an error. It blinks after 30 hours on UCVM downdraft hoods and lights after 40 hours on the other hoods we read. Clean the filters as your manual shows, then press and hold FILTER to reset it. [1][2][3]

Let the glass cool, wash it with mild soapy water, then buff on a little glass cooktop cleaner. Sugar, milk, tomato, plastic film and foil may be scraped off while hot at 20 to 30 degrees; burnt-on residue waits for a damp towel for 30 minutes. [1][2][4]

Wait until the rangetop is cold, wash grates and caps with soap and hot water, clear the cap's port openings with a stiff nylon toothbrush, and dry everything completely before reseating the caps. Never use a steam cleaner, chlorine cleaners or a self-cleaning oven on these parts. [1][3]

Remove the racks and spillage, choose Self Clean with an intensity of 2 to 3 hours and let the door lock; clear the ash after the oven cools. For light soil use Easy Clean with a pan of water and vinegar. A second Self Clean must wait 24 hours. [1][3]

After every steam session empty and dry the water tank and leave the door open until the cavity cools. Run Descaling when the oven asks, mixing 3.5 cups of water with half a bottle of descaler. It lasts about 70 to 90 minutes. Run Ecolytic Clean when dark patches appear. [1][2]

Turn the old filter counterclockwise, move its bottom cap to the new filter, push it in and turn clockwise, then discard the first 24 hours of ice and flush the dispenser for 5 minutes. Finally reset the alert: the method depends on whether you have a 100, 700 or 800, or 900 series. [1][2][3]

E2060 or E12 on the display, or E:20-60 blinking in the DWHD660EFM format. Other E-codes need other steps.
Read the full sequence
The drain pump sends used wash water out of a Thermador dishwasher. Thermador's pages tie it to E22, E23, E24, E25, E6101, E6102 and E6103. Owner steps: reseat the cover over the pump, straighten the drain hose and clear the air gap. A code that keeps returning means a visit.

The filter system catches food particles before they reach the pump. Thermador lists a blocked filter first under E22 and E9240, and says to rinse it under running water with mild soap and a soft brush. The DWHD660EFM guide says to check it after every cycle.
E2060 means limescale has built up in the heat pump, and the dishwasher needs descaling. Use a dishwasher descaler, and softening salt if your machine has a softener.
E12 means limescale has built up in the heat pump. Run a dishwasher descaler through the machine to clear hard-water deposits, and use softener salt if your dishwasher has a softener.
Our technicians look the appliance over before they propose any work. When a part is needed, an OEM part for your model is ordered in.
Repairs under Thermador's manufacturer warranty belong with Thermador. For the work we carry out, we provide our own workmanship warranty.
Burner cleaning, filter care, descaling a coffee system and the routine checks Thermador asks owners to do.
The guide for your model names the interval. We repeat it with the page number.
Yes. Thermador's prompts ask for it, and skipping it can lead to messages. The guide shows the steps.
Anything inside a panel, on a gas line or on wiring. The guide marks those clearly.
Thermador messages, symptoms, parts, repair visits
On a Thermador Pro range, each rangetop burner has its own igniter and should catch within four seconds. If one will not, Thermador’s first suspect is a burner cap sitting out of alignment. Reseat it, dry everything, and check the knob. Several burners dead, or sparking that never stops, needs a technician.
Book a diagnostic made for your exact model and performed at the appliance itself.
Where the offices are, and what to tell us about getting in.