Thermador dishwasher E18 / Water and power supply

Thermador dishwasher
code E18

Dishwasher / display reference

E18 means the water level is too low or water is not being pumped properly. Start with the inlet hose and look for kinks, then confirm the water supply is on; the Thermador manual gives 10 l/min as the flow rate.

Also appears as E18

Last reviewed

Dishwasher / display reference
Meaning
E18 means the water level is too low or water is not being pumped properly. Start with the inlet hose and look for kinks, then confirm the water supply is on; the Thermador manual gives 10 l/min as the flow rate.
Who handles it
Check, then book
Related codes
Source
Error Codes | Dishwashers Support | Thermador

What Thermador dishwasher E18 means.

What it means

E18 means the water level is too low or water is not being pumped properly. Start with the inlet hose and look for kinks, then confirm the water supply is on; the Thermador manual gives 10 l/min as the flow rate.

What you can safely check

Look for kinks or damage.

When to call a technician

E18 stays after the hose check.

Your Thermador steps, stored on this device only

Safe checks, in order.

0 of 4 checks done
  1. Thermador dishwasher E18: Gloved hand holding a dishwasher inlet valve joined by hose to a clear flow meter, with the dishwasher's power plug lying unplugged on the floor
    Illustration. Follow your model’s instructions.
    Before you begin

    Check the inlet hose

    Look for kinks or damage.

  2. Dishwashers in a thoughtfully designed home
    Illustration. Follow your model’s instructions.
    Check 2

    Open the supply

    Make sure the water supply is turned on.

  3. A built-in refrigerator panel flush with cabinetry
    Illustration. Follow your model’s instructions.
    Check 3

    Flow rate

    The Thermador manual says the water flow rate should be 10 l/min.

  4. A technician in a navy shirt holds a tablet showing five empty checkboxes beside a built-in wall oven in a navy kitchen.
    Illustration. Follow your model’s instructions.
    Check 4

    Book a visit

    If the supply and hose are fine.

Is E18 still on the display?

Give us your model number and the checks you already made, then start your request below.

Book a visit

Where a leak is caught.

Conceptual dishwasher sectionTub seam / gasketBase panFloat switchInlet valve1234
  1. 1Tub seam / gasket
  2. 2Base pan
  3. 4Inlet valve

A simplified drawing, since the layout shifts from one model to the next. Tap any outlined part for its photo and the check that goes with it.

A little more context.

What does the DWHD660EFM guide add for the same message?

The guide prints it as E:32-00 and lists three causes. A closed water supply valve: open it, end the cycle, start a new one and call service if it returns. A kinked or blocked inlet hose: call service. A jammed or clogged valve: open it and confirm the flow is at least 10 l/min.

Read the supporting manual

The manual behind the message.

Manufacturer document

Error Codes | Dishwashers Support | Thermador

Thermador / BSH Home Appliances (thermador.com/us support page)

Undated web page; fetched 12.11.2026 / entry "E18"

Manufacturer document

Use and care guide, Dishwasher DWHD660EFM (en-us)

BSH Home Appliances Corporation (Thermador US manual PDF, media3.bsh-group.com)

PDF created 05.08.2026; file tag _C (no printed edition date read) / PDF p33-34, p39-40

Source: the dishwasher error-code page from Thermador, entry E18. The DWHD660EFM guide prints this message as E:32-00 with causes and technical specifications.

Here to help

Good questions.
Clear answers.

Talk to our team
Can low pressure cause it?

The flow-rate hint suggests so. The Thermador manual states a water flow rate of 10 l/min, so weak flow at the taps is worth checking alongside the inlet hose.

Is there a drain link?

Not stated. The Thermador manual describes E18 as a low water level or water not being pumped properly, without linking it to the drain, and lists no drain-hose check.

Do I measure?

No, just check the taps. Make sure the water supply is turned on and the inlet hose has no kinks; the 10 l/min figure is what a technician measures against.

When to book?

Book a visit if the inlet hose and supply check out and E18 stays, or if water stands in the tub or never fills.

How much water pressure does the dishwasher need?

The DWHD660EFM guide gives 7.25 to 145 psi (50 to 1,000 kPa) and a minimum inlet rate of 2.6 gal/min. A technician can measure both; mention any low-flow signs at other taps.

Let’s take care of it.

One burner, two burners,
or the whole range.