What it means
E0106 means the circuit that drives the wash arm diverter on the main control board has a problem. Reset power at the breaker for 30 seconds; if E0106 returns, book a technician.
Thermador dishwasher E0106 / Control board and sensors
E0106 means the circuit that drives the wash arm diverter on the main control board has a problem. Reset power at the breaker for 30 seconds; if E0106 returns, book a technician.
Also appears as E0106
E0106 means the circuit that drives the wash arm diverter on the main control board has a problem. Reset power at the breaker for 30 seconds; if E0106 returns, book a technician.
Mention whether the spray arms ran.
E0106 returns after the breaker reset.
Your Thermador steps, stored on this device only

Mention whether the spray arms ran.

Off for 30 seconds, then on.

Check whether water reaches both arms.

The board is a technician job.
Give us your model number and the checks you already made, then start your request below.
Book a visit
A simplified drawing, since the layout shifts from one model to the next. Tap any outlined part for its photo and the check that goes with it.
The Thermador manual names a wash arm diverter circuit on the main board, and gives no part detail.
Read the supporting manualE0103 and E0107 are relay messages; E0106 concerns the diverter circuit.
Read the supporting manualReset once, then decide.
Read the supporting manualThe dishwasher page gives the same breaker reset to E0100 (heat pump motor circuit at the main control board), E0103 and E0107 (main control board relay), E2030 and E6001 (heat pump internal heater), E2120 and E2130 (Zeolite chamber heater and fan motor), E6002, E6900 and E8000.
Read the supporting manualManufacturer document
Thermador / BSH Home Appliances (thermador.com/us support page)
Undated web page; fetched 12.11.2026 / entry "E0106"
Manufacturer document
BSH Home Appliances Corporation (Thermador US manual PDF, media3.bsh-group.com)
PDF created 05.08.2026; file tag _C (no printed edition date read) / PDF p35
Source: the dishwasher error-code page from Thermador, entry E0106. The DWHD660EFM guide does not list this code; it is cited only for its general electronics reset.
Not stated. The Thermador manual says only that the circuit driving the wash arm diverter has a problem, so test a cycle and note whether water reaches both arms.
The Thermador manual says the circuit on the main control board has a problem, and the board is a technician job. It does not say the whole board is failing.
No owner step is printed. Reset the breaker for 30 seconds, and if E0106 returns, the board is a technician job.
Book a visit. If E0106 returns after the 30-second breaker reset, tell us every code you saw, including any neighboring ones.
The Thermador manual says 30 seconds for E0106. A different reset in the DWHD660EFM guide, for when all indicators light or flash, asks for at least 2 minutes. That guide does not list E0106 itself. [2]
Thermador messages, symptoms, parts, repair visits
E0103 means a relay on the main control board of a Thermador dishwasher has a problem. Reset power at the breaker for 30 seconds; if the message stays, call for a technician.
For a Thermador dishwasher that leaves water behind, the error-code page lists the same four steps for E22, E24 and E25: filter, drain pump cover, drain hose and air gap or hose. The DWHD660EFM guide adds two checks for a display reading E:61-03: remove the garbage disposal plug and keep a high loop in the hose.
Book a diagnostic made for your exact model and performed at the appliance itself.
Where the offices are, and what to tell us about getting in.